Free Samples
NEF2251 Fundamentals Of Electrical And Electronic Engineering
.cms-body-content table{width:100%!important;} #subhidecontent{ position: relative;
overflow-x: auto;
width: 100%;}
NEF2251 Fundamentals Of Electrical And Electronic Engineering
0 Download8 Pages / 1,823 Words
Course Code: NEF2251
University: Victoria University
MyAssignmentHelp.com is not sponsored or endorsed by this college or university
Country: Australia
Question:
Describe the Fundamentals of Electrical and Electronic Engineering.
Answer:
Introduction
The objective of this experiment is to study and get acquainted with/to a balanced three-phase Y-to- Y connected system. In this experiment, a 3-phase Y connected voltage source will be connected to a 3-phase Y-connected load with various measurements taken to validate the relationship between line and phase voltages. Students will so be expected to determine the load impedance from the measurements taken during the experiment. The entire experiment will be conducted at 50 Hz. All of the currents and voltages in this experiment are RMS quantities.
Background Summary and Preliminary
The power is generated, transmitted, and distributed in 3-phase (3-Φ) form. The 3-Phase AC supply system has the following advantages:
It is themost economical wayof generating, transmitting, and distributing electrical energy
It can supplyawide variety of loads, those that require a three-phase supply such as an induction motor, as well as others requiring only a single phase supply
A balanced three-phasesystem ensures asmooth flow of energy from source to load since single-phase power produces a pulsating flow of energy
2.1 Balanced Three-Phase System
Figure 1 shows the circuit diagram of the three-phase circuit that will be connected up for this experiment. A three-phase Y-connected RLC load bank is to be connected to a Y-connected three- phase voltage source.
Figure 2 shows the per-phase circuit (phase U) of the load bank. It is possible to alter the phase impedances (ZU, ZV, and ZW) of the load bank individually by adjusting the reactances XU, XV, and XW as well as the resistances RU, RV, and RW in each phase. The reactances and resistances can be adjusted by using the three knobs available on the RLC load bank. In this experiment, a balanced three-phase load is required. Therefore, XU = XV = XW and RU = RV = RW. The settings for the reactance and resistances will be provided to you by your lab supervisors during the experiment.
It is also possible to set the load as an inductive or capacitive load by using the 3-way switch available on the RLC load bank. If XL is chosen, the power factor will be a positive value and a negative value if XC is chosen.
Preliminary
Please refer to your lecture and tutorial notes for more information in relation to 3-Phase systems. Each student is expected to answer the following pre-lab questions in the space provided by applying the theory gained in lectures and tutorials. The pre-lab exercises must be completed before the start of the experiment. Students will not be given time before the start of the experiment to do the preliminary work. Students who fail to do their preliminary will not be allowed to carry out the experiment. Completion of the preliminary is important, as this will help students to perform an analysis of the experiment to bring them up to date with the theoretical background.
Pre-Lab Question1: Draw the circuit diagram of a 3-phase Y-connected voltage source clearly labelling all phase and line voltages. Also, write down the mathematical formulas that express the relationship between phase voltages, and phase and line voltages. Are the line voltages greater in magnitude or phase voltages?
Line voltage: is the voltage measured between the any two-line segments, line voltage are voltage between two live conductors.
Phase voltage: voltage measured between live and the neutral link of the three-phase supply system.
For star connected circuit and for the relation between line and phase current given as
During laboratory experiment we have recorded
Table 1 Observation line and phase voltage
Van
243 Volts
Vbn
242Volts
Vcn
239Volts
Vab
419Volts
And from mathematical relationship line voltage is 1.73 times the phase voltage so line voltage is more than the phase voltage
Pre-Lab Question2: Write down the relationship between the peak and RMS values of a voltage. What are the peak and RMS values of the mains voltage in the Australia?
Solution:
The relationship between the peak and RMS values of a voltage is
The main voltage in Australia is 230 V at 50 Hz frequency therefore the RMS value of mains voltage in Australia is 230 V
Thus, the peak value of mains voltage in Australia is
Pre-Lab Question 3: For the following Δ (delta) connected load, if the phase impedance is 18 + 21j ?/Φ, what
Pre-Lab Question 4: What is the neutral current in a 3-phase 4 Wire Balanced System? And why?
Solution:
The neutral current is zero in three phase Star configuration in balanced load while it gives some value of current in unbalanced load. In a Star 4 wire system the neutral, in theory, carries only the difference of current flow between the 3 phase conductors. So, when the current in phase A, B and C are equal, then there is no current flow in the neutral. When current flow in phase A only increases, then the neutral current will equal that increase. However, this is true only for purely resistive (linear) loads. Non-linear loads cause harmonics, some of which will add up on the neutral. Because when you add all the currents together at the neutral they add up to 0 if they are balanced. If balanced current was 10A/ phase then add 10cos(0) + 10cos(-120)+10cos(120) = 0 for a 3 phase system. If it’s not balanced then add them all together and there will be some current at some angle left over
Pre-Lab Question 5: What is the per-unit system? How are the actual circuit quantities (voltages, currents, impedances, etc) converted to their per-unit values? If the 3-? apparent power (|S|) rating of a 3-phase Y-to-Y connected load is 5 kVA and line voltage is 415 Volts, what would be the base impedance?
Solution:
The per unit system simplifies the analysis of complex power system by choosing a common set of base parameters in terms of which all system quantities are defined
The definition of any quantity (voltage, current, impedance) in per unit system is given as
The
Voltage: the ratio of actual voltage to the base voltage is called the per unit voltage
Vbase- base voltage or rated voltage
Current: the ratio of actual current to base current is called p.u. current
Similarly ration of actual impedance to the base impedance is called per unit impedance
Here for given problem
For the single-phase system
And for three phase system
And for current
Base impedance
Measurement Results When X = XL (Inductive Load)
Quantity
Value
XU = XV = XW
0.5pu=0.5pu=0.5pu
RU = RV = RW
0.5pu=0.5pu=0.5pu
Van
243 Volts
Vbn
242Volts
Vcn
239Volts
Vab
419Volts
ILine-a
6.7Amps
Ineutral
339Amps
P?
780Watts
Cos θ
0.48
Switchthe load bank off by using on-off switch on the load bank.
Changethe position of the 3-way switch to point to the XC setting
Re-energiesthe RLC load bank by turning on the on-off switch
Redothemeasurements and record the values of the circuit quantities in the table provided below
Measurement Results When X = XC (Capacitive Load)
Quantity
Value
XU = XV = XW
0.5pu=0.5pu=0.5pu
RU = RV = RW
0.5pu=0.5pu=0.5pu
Van
243 Volts
Vbn
242 Volts
Vcn
240 Volts
Vab
419 Volts
ILine-a
6Amps
Ineutral
1.9 Amps
P?
775 Watts
Cos θ
-0.5
1) The Preliminary Work
2) Measurements recorded during the experiment including the nameplate information in tabulated form
Nameplate Information of the RLC Load Bank
Model
Apparent Power (|S|)
Voltage Rating
Current Rating
Frequency
Power factor
3) The calculation of the XU = XV = XW and RU = RV = RW actual values, i.e. the conversion from the per-unit values.
4) The calculation of the per-phase load impedance of the Y-connected load (Refer to Class Example 2) for both the X = XL and X = XC cases. How does ZY for X = XL differ from ZY for X = XC and why?
Phase current: I1p = I1L, I2p = I2L, I3p = I3L
Line current: IL = I1L = I2L = I3L
Phase voltage:
Line voltage: VL = V12 = V23 = V31
For X = XL
The per phase impedance remains the same in start connected circuit no conversion is needed so for the both cases it can be written as
5) The computation of the per-phase load impedance of an equivalent Δ-connected load
The equivalent impedance is given as
As its balance load circuit all impedance are same so the per phase equivalent impedance is give as
6) From the measurements, determine the mathematical relationship between the magnitudes of the line voltage and line-to-neutral voltage for phase a. Does it agree with the theoretical principles?
According to readings
References:
[1] Louis, M.M., 2014. Elements of Electrical Engineering. PHI Learning Pvt. Ltd.
[2] Dorf, R.C., 2018. Pocket book of electrical engineering formulas. CRC Press.
[3] Bird, J., 2017. Electrical circuit theory and technology. Routledge.
[4] Mayergoyz, I.D. and Lawson, W., 1997. Basic electric circuit theory: a one-semester text. Gulf Professional Publishing.
Free Membership to World’s Largest Sample Bank
To View this & another 50000+ free samples. Please put
your valid email id.
Yes, alert me for offers and important updates
Submit
Download Sample Now
Earn back the money you have spent on the downloaded sample by uploading a unique assignment/study material/research material you have. After we assess the authenticity of the uploaded content, you will get 100% money back in your wallet within 7 days.
UploadUnique Document
DocumentUnder Evaluation
Get Moneyinto Your Wallet
Total 8 pages
PAY 5 USD TO DOWNLOAD
*The content must not be available online or in our existing Database to qualify as
unique.
Cite This Work
To export a reference to this article please select a referencing stye below:
APA
MLA
Harvard
OSCOLA
Vancouver
My Assignment Help. (2021). Fundamentals Of Electrical And Electronic Engineering. Retrieved from https://myassignmenthelp.com/free-samples/nef2251-fundamentals-of-electrical-and-electronic-engineering/phase-voltages.html.
“Fundamentals Of Electrical And Electronic Engineering.” My Assignment Help, 2021, https://myassignmenthelp.com/free-samples/nef2251-fundamentals-of-electrical-and-electronic-engineering/phase-voltages.html.
My Assignment Help (2021) Fundamentals Of Electrical And Electronic Engineering [Online]. Available from: https://myassignmenthelp.com/free-samples/nef2251-fundamentals-of-electrical-and-electronic-engineering/phase-voltages.html[Accessed 18 December 2021].
My Assignment Help. ‘Fundamentals Of Electrical And Electronic Engineering’ (My Assignment Help, 2021)
My Assignment Help. Fundamentals Of Electrical And Electronic Engineering [Internet]. My Assignment Help. 2021 [cited 18 December 2021]. Available from: https://myassignmenthelp.com/free-samples/nef2251-fundamentals-of-electrical-and-electronic-engineering/phase-voltages.html.
×
.close{position: absolute;right: 5px;z-index: 999;opacity: 1;color: #ff8b00;}
×
Thank you for your interest
The respective sample has been mail to your register email id
×
CONGRATS!
$20 Credited
successfully in your wallet.
* $5 to be used on order value more than $50. Valid for
only 1
month.
Account created successfully!
We have sent login details on your registered email.
User:
Password:
MyAssignmenthelp.com delivers assignment help to millions of students of USA. We have in-house teams of assignment writers who are experts on wide ranges of subjects. We have appointed teams of native writers who provide assignment help to students in New York City and all over the USA. They are skilled assignment writers who successfully cater to search terms like do my assignment in the USA
Latest Management Samples
div#loaddata .card img {max-width: 100%;
}
MPM755 Building Success In Commerce
Download :
0 | Pages :
9
Course Code: MPM755
University: Deakin University
MyAssignmentHelp.com is not sponsored or endorsed by this college or university
Country: Australia
Answers:
Introduction
The process of developing a successful business entity requires a multidimensional analysis of several factors that relate to the internal and external environment in commerce. The areas covered in this current unit are essential in transforming the business perspective regarding the key commerce factors such as ethics, technology, culture, entrepreneurship, leadership, culture, and globalization (Nzelibe, 1996; Barza, 2…
Read
More
SNM660 Evidence Based Practice
Download :
0 | Pages :
8
Course Code: SNM660
University: The University Of Sheffield
MyAssignmentHelp.com is not sponsored or endorsed by this college or university
Country: United Kingdom
Answers:
Critical reflection on the objective, design, methodology and outcome of the research undertaken Assessment-I
Smoking and tobacco addiction is one of the few among the most basic general restorative issues, particularly to developed nations such as the UK. It has been represented that among all risk segments smoking is the fourth driving purpose behind infections and other several ailments like asthma, breathing and problems in the l…
Read
More
Tags:
Australia Maidstone Management Business management with marketing University of New South Wales Masters in Business Administration
BSBHRM513 Manage Workforce Planning
Download :
0 | Pages :
20
Course Code: BSBHRM513
University: Tafe NSW
MyAssignmentHelp.com is not sponsored or endorsed by this college or university
Country: Australia
Answer:
Task 1
1.0 Data on staff turnover and demographics
That includes the staffing information of JKL industries for the fiscal year of 2014-15, it can be said that the company is having problems related to employee turnover. For the role of Senior Manager in Sydney, the organization needs 4 managers; however, one manager is exiting. It will make one empty position which might hurt the decision making process. On the other hand, In Brisba…
Read
More
MKT2031 Issues In Small Business And Entrepreneurship
Download :
0 | Pages :
5
Course Code: MKT2031
University: University Of Northampton
MyAssignmentHelp.com is not sponsored or endorsed by this college or university
Country: United Kingdom
Answer:
Entrepreneurial ventures
Entrepreneurship is the capacity and willingness to develop, manage, and put in order operations of any business venture with an intention to make profits despite the risks that may be involved in such venture. Small and large businesses have a vital role to play in the overall performance of the economy. It is, therefore, necessary to consider the difference between entrepreneurial ventures, individual, and c…
Read
More
Tags:
Turkey Istanbul Management University of Employee Masters in Business Administration
MN506 System Management
Download :
0 | Pages :
7
Course Code: MN506
University: Melbourne Institute Of Technology
MyAssignmentHelp.com is not sponsored or endorsed by this college or university
Country: Australia
Answer:
Introduction
An operating system (OS) is defined as a system software that is installed in the systems for the management of the hardware along with the other software resources. Every computer system and mobile device requires an operating system for functioning and execution of operations. There is a great use of mobile devices such as tablets and Smartphones that has increased. One of the widely used and implemented operating syste…
Read
More
Tags:
Australia Cheltenham Computer Science Litigation and Dispute Management University of New South Wales Information Technology
Next